Canon TS705 Edible Printer – How to Clean Feed Rollers

TS705 Edible Printer Kit
How to Clean Feed Rollers on Canon Printer TS705

If the paper feed roller is dirty or paper powder is attached to it, paper may not be fed properly.

In this case, clean the paper feed roller. Cleaning will wear out the paper feed roller, so perform this only when necessary.

s without Paper:

  • Check that printer is turned on.
  • Remove any paper from paper source to clean rollers.
    • If a message appears on the screen, check it and then press the OK button.
  • Press the Setup button (top right next to LCD screen) , use the left right button to select Maintenance, and press the OK button.
  • Use left right button to select Roller Cleaning and press OK button.
  • Use left right button to select paper source (Rear tray) to clean rollers and press OK button.

    The paper feed roller will rotate as it is cleaned without paper.

Cleaning the Feed Rollers with Paper:

  • Make sure paper feed rollers have stopped rotating, and then load three sheets of A4 or Letter-sized plain paper in paper source selected in step 4
    • Press the OK button.

      The printer starts cleaning. The cleaning will be complete when the paper is ejected.

 

How to Print A Nozzle Check Pattern on Canon TS705 Printer

If you’re having problems with the quality of your printing, a good place to start is by carrying out a nozzle check. When printers are unused for long periods of time (especially if you’re edible printing) this can cause problems with your printhead. Running a nozzle check will help to establish whether any of the nozzles are blocked.

Printing the Nozzle Check Pattern

Please note: If the remaining ink level is low in any of your cartridges, the nozzle check pattern will not be printed correctly. Replace/ fill the ink cartridge whose ink is low.

  1. Make sure that the power on your Canon TS705 printer is turned on.
  2. Load a sheet of A4 plain paper in the rear tray (if you’re edible printing don’t waste your icing sheets, using normal copier paper is fine for this task and won’t cause any damage).
  3. Press the Setup button on the LCD display panel, use the arrow buttons to select maintenance and press OK
  4. Use the arrow button to select nozzle check and press OK
  5. The nozzle check will then be printed

Do not perform any other tasks until the printer completes the printing of the nozzle check pattern

What Should the Nozzle Check Pattern Look Like?

Examine the nozzle check pattern, and clean the print head if necessary.

Check if there are missing lines in the pattern (A) or horizontal white streaks in the pattern (B).

  • (C) Number of sheets printed so far 

Cleaning the print head is required if:

  1. There are missing lines in the pattern (A), see example below:

(D) Good        (E) Bad (lines are missing)

2. There are horizontal white streaks in the pattern (B)

3. If any colours are missing altogether

We’ve found the best way to clean the printhead is to remove it from the printer and run it under hot water (as hot as you can stand it).

 

How To Print the Nozzle Check Pattern on Canon IX6850 Printer

If you’re having problems with the quality of your printing, a good place to start is by carrying out a nozzle check. When printers are unused for long periods of time (especially if you’re edible printing) this can cause problems with your printhead. Running a nozzle check will help to establish whether any of the nozzles are blocked.

Printing the Nozzle Check Pattern

Please note: If the remaining ink level is low in any of your cartridges, the nozzle check pattern will not be printed correctly. Replace/ fill the ink cartridge whose ink is low.

  1. Make sure that the power on your IX6850 printer is turned on.
  2. Load a sheet of A4 plain paper in the rear tray (if you’re edible printing don’t waste your icing sheets, using normal copier paper is fine for this task and won’t cause any damage).
  3. Open the front cover gently, then pull out the paper output tray.
  4. Hold down the RESUME/CANCEL button until the POWER lamp flashes white twice, then release it immediately. This is the lower orange button on the RHS of the printer

    The nozzle check pattern will be printed.

    Do not perform any other operations until the printer completes the printing of the nozzle check pattern.

What Should the Nozzle Check Pattern Look Like?

Examine the nozzle check pattern, and clean the print head if necessary.

  1. Check if there are missing lines in the pattern (A) or horizontal white streaks in the pattern (B).
    • (C) Number of sheets printed so far

Cleaning the print head is required if:

  1. If there are missing lines in the pattern (A):
  • (D) Good
  • (E) Bad (lines are missing)

2. If there are horizontal white streaks in the pattern (B):

  • (F) Good
  • (G) Bad (horizontal white streaks are present)

3. If there are colours missing altogether

We’ve found the best way to clean the printhead is to remove it from the printer and run it under hot water (as hot as you can stand it).

 

Cleaning and Maintaining your Edible Printer

It’s important to adopt regular cleaning and maintenance practices from the start to get the best results from your edible printer and prolong it’s life.

We’re often asked how often should I clean my printer? This depends how often it’s being used. If it’s used frequently then carrying out weekly maintenance is good practice.

If the printer is used infrequently we strongly suggest you remove the cartridges from the printer, insert them back into the orange cradles supplied with your refillable cartridges and undertake a full printhead clean (see point 3 below). So next time you come to use your printer, all you need to do is re-insert your cartridges and away you go. Failure to do this and leaving the printer unused can cause the printhead to block. Edible ink is made from sugar which tends to crystallise on the printhead if left unused for too long.

For your weekly maintenance routine please find below screenshots and instructions for :

  1. ROLLER CLEANING (PART 1)
  2. ROLLER / PLATE CLEANING (PART 2) ( eliminating teeth / ‘tram’ lines)
  3. (Removal of) AND CLEANING THE PRINT HEAD- incl. links to videos
  4. TEST PRINT PAGE AND PRINT HEAD ALIGNMENT

These instructions (incl screenshots) have been created using an (Apple) Mac computer.
Instructions will be similar for Windows PC / Laptops.

Settings (Control Panel on a Windows PC)

Find your printer:

Click on Utility / open printer utility:

1 – ROLLER CLEANING

The Cleaning (drop down menu) should be the default menu showing 4 options :

Click on Roller Plate Cleaning (4th option / last option)

We then advise to click on the 3rd option where you insert A4 standard paper to clean rollers (see next step):

2 – ROLLER / PLATE CLEANING ( eliminating teeth / ‘tram’ lines)

After option 4, choose option 3 to clean the bottom plate.

Follow the instructions and fold a piece of standard A4 paper (not wafer paper or icing sheet) into a concertina pattern.

TIP – smear a small amount of sanitising gel across the peaks of the folds on both sides.

This helps to attract / clean dirt from the roller teeth (especially good if you have been getting ‘tram lines’ on your prints after printing dark colours

WARNING ! – DO NOT put too much sanitising gel on the folds else the paper may tear and get stuck inside the printer ! Use a smallish quantity and repeat many times . It is amazing how much ink comes off the roller teeth !

3 – (removal of) AND CLEANING PRINT HEAD :

Please see the following link to Youtube videos showing how to remove the print head for cleaning for ip7250 / MG5750-51 / TS5050-51 Printers : https://www.youtube.com/channel/UCPciNQLUjHtyclZcOIa7Afg

AFTER REMOVING/ RE-INSERTING A PRINT HEAD OR IF YOU HAVE BLOCKAGES IN THE PRINT HEAD, CHOOSE OPTION 2 FROM THE CLEANING MENU TO DEEP CLEAN THE PRINT HEAD:

4 – TEST PRINT PAGE AND PRINT HEAD ALIGNMENT

To print a test page, scroll down the menu on the printer utility to Test Print and follow the instructions

Choose Nozzle Check.

Sometimes, if the printer is not playing ball, or if you have removed and replaced the print head after cleaning, you may need to re-align the print head.

If you have never gone through this process before, you may be wondering, “What is a printhead alignment?” In a nutshell, a printhead alignment synchronizes the paper feed with the movement of the printhead, ensuring you get the best print quality possible.

Remember adopting best practices from the beginning will save you time, money and stress in the long run!

Good luck.

Common Problems with Edible Ink Cartridges

 

Edible Ink cartridges

If you’re experiencing problems with your edible ink cartridges, we’ve compiled a quick checklist of common issues:

The Cartridges won’t register on my printer

  • If you’re using reflllable cartridges you must ensure both the cavity and sponge side of the cartridge are full – otherwise the cartridges won’t be heavy enough to register on the printer Edible Ink Refill Set
  • You may have been sent the wrong cartridges. The easiest way to check is to read the chip on the underside of the cartridge. If you’ve ordered a Canon IP7250 edible printer or the Canon IX6850 the number on the chip should start 550 or 551. If you’ve ordered the Canon TS5050 the number on the chip should start 570 or 571 and for the Canon TS705 or TS6350 this number begins with 580 or 581. If these numbers don’t correspond with your printer then please contact us on sales@edibleprintsupplies.co.uk and we’ll replace your cartridges.
  • When you insert the cartridges into the printer please ensure you’ve removed the orange cradles

 

  • If inserted correctly you should hear the cartridges click into place and the light on the cartridges should illuminate
  • If the cartridges don’t click into place you may need to pull the lever at the front of the cartridges towards you a little so the cartridges fit correctly (be gentle to ensure the lever doesn’t snap off)
  • If the cartridges still don’t illuminate please turn off the printer at the power supply for a few seconds and then re-start the printer
  • Refillable edible ink cartridges don’t last forever and should be replaced at least every 6 months. If they’ve been working fine and just stopped working there’s a good chance you need to replace them.

The ink won’t come out of the cartridges

  • Please ensure you’ve removed the ‘Pull’ strip on top of the cartridges
  • If the ink still won’t come out of the cartridge there is a small soft breathe hole on top of the cartridge (this would have been under the pull strip at the opposite end to the coloured plug), please prick this with a pin or needle. This helps the air and ink to flow through the cartridge. Press onto the soaker sponge underneath the cartridge (where the ink comes out)with a cotton bud or something similar (please ensure you wear gloves) until the ink starts flowing
  • Again, please make sure both the cavity and sponge side of the cartridge are full of ink

Ink is Pouring out of the Cartridges

  • Please ensure you fill the cartridges whilst they are still on the orange cradles otherwise the ink will pour from the bottom.
  • Once both the cavity and sponge side of the cartridge is full of ink replace the coloured plug. Remove the cartridge from it’s cradle and swiftly insert it into the printer (again we recommend wearing gloves!)
  • You must keep the orange cradles for re-filling the cartridges next time they are empty

There’s an error message saying ‘ink tank cannot be recognised’

  • Please ensure you’ve ordered the correct cartridges for your printer, or we’ve sent you the correct cartridges – occasionally although we try to avoid them, mistakes do happen.
  • If you’ve ordered a Canon IP7250 edible printer or the Canon IX6850 the number on the chip should start 550 or 551. If you’ve ordered the Canon TS5050 the number on the chip should start 570 or 571. For the TS705 or TS6350 printer they should begin with 580 or 581. If these numbers don’t correspond with your printer then please contact us on sales@edibleprintsupplies.co.uk
  • If you’re using reflllable cartridges you must ensure both the cavity and sponge side of the cartridge are full – otherwise the cartridges won’t be heavy enough to register on the printer
  • Refillable edible ink cartridges don’t last forever and should be replaced at least every 6 months. If they’ve been working fine and just stopped working there’s a good chance you need to replace them.
  • The cartridges won’t work unless you’re using the correct coloured cartridge ie. if you try to insert a magenta cartridge into the printer where a yellow cartridge should be it won’t work. Each cartridge has a specially formatted chip to work with the corresponding colour.

I Haven’t Used My Printer for a While and the Cartridges Won’t Work

  • There’s a good chance the cartridges / printhead will have become clogged if you’ve not used your edible printer for a while. The best remedy for this is to remove your printhead and give it a good clean under running warm water
  • Once the print head is in position, turn off the power cable to stop the print head returning to the hidden right position.
  • To clean the print head, run it under  hot water for 3-4 minutes, rotating it so that the water runs into the top downwards and also back through the bottom with the water running back through the other way.
  • YES, the print head DOES have electronic parts, but it is perfectly safe to get these wet also, just DO NOT SUBMERGE the print head in water, or leave it in water for a long period.
  • Dry the print head with kitchen paper as much as possible prior to replacing.
  • It will take 3 or 4 new print outs to get the ink flowing again, so we advise you print a test page or nozzle check first thing after replacing the print head. This will show you that the head is fully clean again per the print pattern.
  • If this still doesn’t work, then we suggest purchasing a new set of cartridges

How to Remove Print Head for Cleaning on Canon TS5050 & TS5051 Printers

This simple video shows how to remove the print head for cleaning on the Canon Pixma TS5050 and TS5051 printers.

https://www.youtube.com/watch?v=ccDUI6cjoOU

Tips –

  • Once the print head is in position, turn off the power cable to stop the print head returning to the hidden right position.
  • To clean the print head, run it under  hot water for 3-4 minutes, rotating it so that the water runs into the top downwards and also back through the bottom with the water running back through the other way.
  • YES, the print head DOES have electronic parts, but it is perfectly safe to get these wet also, just DO NOT SUBMERGE the print head in water, or leave it in water for a long period.
  • Dry the print head with kitchen paper as much as possible prior to replacing.
  • It will take 3 or 4 new print outs to get the ink flowing again, so we advise you print a test page or nozzle check first thing after replacing the print head. This will show you that the head is fully clean again per the print pattern.

 

 

How to Wash a Clogged Print Head for Canon ip7250 ix6850 MG5750 MG5751 TS5050 Printers

How to wash or rinse the print head for a Canon 5750/5751/5752/5753 and ip7250 ix6850 Pixma and the latest edible food printer, the Canon TS5050 rear feed printer.

Following the previously posted video to remove the print head on Canon printers, this video shows how to safely wash or rinse the print head in the event of a clogged print head.

Edible Print Supplies advises that users of Edible Food Printers regularly remove and wash the print heads, even if they are not clogged. This preventative maintenance will save time, effort and cost in the long run – most importantly saving time when you need to urgently print but unfortunately suffer a clogged print head !

Please call EPS on 01254 825786 if you require any printer advice for printing on Edible Icing sheets, wafer paper including coloured and flavoured wafer paper and meringue and chocolate cocoa transfer sheets.

Or contact sales@edibleprintsupplies.co.uk

We take pride in supporting all customers with technical issues

Thank you and Enjoy Edible Printing !

How to Remove Print Head for Cleaning on Canon ip7250 & ix6850 Printers

 

Screen Shot 2017-05-31 at 11.29.36

How to remove the print head for cleaning on a Canon ip7250 / 7200 series / ix6850 Pixma series printers.
Video shows removal of Cartridges and then removal and replacement of print head.
Please call EPS on 01254 825786 if you require any printer advice for printing on Edible Icing sheets, wafer paper and meringue and chocolate cocoa transfer sheets.
Or contact sales@edibleprintsupplies.co.uk
We take pride in supporting all customers with technical issues
Thank you and Enjoy Edible Printing !

 

How to Remove Print Head for Cleaning on Canon MG5750 MG5751 Printer

print head removal for canon pixma MG5750 5751 Printer

How to remove the print head for cleaning on a Canon 5750/5751/5752/5753 and 6850 Pixma series printers.
Video shows removal of Cartridges and then removal and replacement of print head.
Please call EPS on 01254 825786 if you require any printer advice for printing on Edible Icing sheets, wafer paper and meringue and chocolate cocoa transfer sheets.
Or contact sales@edibleprintsupplies.co.uk
We take pride in supporting all customers with technical issues
Thank you and Enjoy Edible Printing !